Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11.10.1. Replacement of torsions of a trunk lid
11.10.2. Removal and installation of a trunk lid
11.10.3. Replacement of the lock, latch and switch of the lock of a trunk lid
11.10.4. Removal and installation of the drive of the lock of a trunk lid
11.10.5. Removal and installation of a decorative overlay of a trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








59d80679


11-10-4-snyatie-i-ustanovka-privoda-zamka-kryshki-bagazhnika.html

11.10.4. Removal and installation of the drive of the lock of a trunk lid

You will need a key "on 10" (more convenient to use a face head).
1. Disconnect a drive cable from the trunk lid lock, having removed the lock from the body back panel (see. "Replacement of the lock, latch and switch of the lock of a trunk lid").
2. Remove forward and back facings of the left threshold of a floor (see. "Removal and installation of facings of salon").
3. Remove facings of an arch of the left back wheel and the left back lamp (see. "Removal and installation of facings of a luggage carrier").

NOTE
Facing of the panel of a back was removed in the course of removal of the lock of a luggage carrier (see item 1).

4. Turn out through a window in a floor rug a bolt of fastening of the block of handles.
5. Unbend edge of a rug and take from under a rug the block of handles together with cables of drives, having stretched the block through a window in a floor cross-piece.
6. Take out a tip of a cover of a cable of the drive of the lock of a luggage carrier from a cut of an arm of the block of levers and, having taken out a cable tip from a lever cut, disconnect a cable.

NOTE
If necessary similarly disconnect from the block of handles a cable of the drive of the lock of a cover of the hatch of a bulk pipe of the fuel tank (with a white tip) and remove the block of handles.

7. Take a cable cover from holders on the left threshold of a floor and remove a luggage carrier lock drive cable, extending it in a luggage carrier through an opening in a body partition.
8. Install the drive of the lock of a luggage carrier and all removed details as it should be, the return to removal. If necessary adjust the drive (see the item 7 of the subsection "Replacement of the Lock, Latch and Switch of the Lock of a Trunk Lid").

"previous page
11.10.3. Replacement of the lock, latch and switch of the lock of a trunk lid
following page"
11.10.5. Removal and installation of a decorative overlay of a trunk lid