Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








59d80679


11-5-snyatie-i-ustanovka-bryzgovikov-koles-i-podkrylkov.html

11.5. Removal and installation of mudguards of wheels and flaps

In arches of forward wheels and in a back part of arches of back wheels the plastic flaps protecting a body from the abrasive influence of sand and stones rejected by wheels are installed. The mudguards established behind forward wheels protect body thresholds. Back mudguards protect the cars going afterwards from damage by the stones which are taking off from under back wheels.
It will be required to you: the screw-driver with a crosswise edge, a key rattle with a crosswise bat for an otvorachivaniye of remote screws.

    
NOTE
Work is shown for mudguards and flaps on the left side of the car. The right mudguards and flaps are removed and established similarly.

For removal of a mudguard of a forward wheel execute the following operations.
1. Turn out the screw of the lower fastening …
2. … and two screws of forward fastening of a mudguard to a forward wing …
3. … then remove a mudguard of a forward wheel.
4. Establish a mudguard of a forward wheel as it should be, the return to removal.

For removal of the forward flap execute the following operations.
1. Remove a mudguard of a forward wheel (see above in this subsection).
2. Turn out three screws of fastening of the flap to a front bumper.
3. Push (for example, the screw-driver) the core of a percussion cap of forward fastening of the flap in a percussion cap …
4. … also remove a percussion cap.
5. Similarly remove two percussion caps of the top fastening …
6. … on one percussion cap of back fastening above …
7. … and below …
8. … then remove the forward flap.
9. Install the forward flap as it should be, the return to removal.

For removal of a mudguard of a back wheel execute the following operations.
1. Turn out the screw of the lower fastening …
2. … and two screws of forward fastening of a mudguard to a rear bumper …
3. … also remove a mudguard of a back wheel.
4. Establish a mudguard of a back wheel as it should be, the return to removal.

For removal of the back flap execute the following operations.
1. Remove a mudguard of a back wheel (see above in this subsection).
2. Turn out two top screws …
3. … and one lower screw of fastening of the flap to a rear bumper …
4. … then remove the back flap.
5. Install the back flap and all removed details as it should be, the return to removal.

"previous page
11.4. Removal and installation of facing of a radiator
following page"
11.6. Removal and installation of a forward wing