Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of laying of a cover of a head of the block of cylinders
5.7.2. Replacement of laying of a head of the block of cylinders
5.7.3. Replacement of oil scraper caps
5.7.4. Replacement of an epiploon of the camshaft
5.7.5. Replacement of epiploons of a bent shaft
5.7.6. Replacement of consolidation of an oil case
5.7.7. Replacement of laying of an inlet pipe
5.7.8. Replacement of laying of a final collector
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








59d80679


5-7-4-zamena-salnika-raspredelitelnogo-vala.html

5.7.4. Replacement of an epiploon of the camshaft

At detection of traces of dribble of oil through a camshaft epiploon at first check whether the system of ventilation of a case is littered and whether hoses of system of ventilation of a case are pressed, if necessary eliminate malfunctions. If the leak of oil does not stop, replace an epiploon.
It will be required to you: all tools necessary for removal of the drive of the gas-distributing mechanism (see. "Replacement and adjustment of a tension of a belt of the drive of the gas-distributing mechanism and replacement of its tension roller"), and also a key "on 17", the screw-driver, passatizh, the hammer.
1. Disconnect a wire from the minus plug of the rechargeable battery.
2. Install the piston of the 1st cylinder in the provision of VMT of a step of compression (see. "Installation of the piston of the first cylinder in the provision of VMT of a step of compression").
3. Take off a belt of the drive of the gas-distributing mechanism (see. "Replacement and adjustment of a tension of a belt of the drive of the gas-distributing mechanism and replacement of its tension roller").
4. Turn out a bolt of fastening of the cogged pulley of the camshaft, holding a pulley from a provorachivaniye, as shown in a photo, the handles inserted into pulley openings the passatizhy and big screw-driver …
5. … also remove a pulley.
6. Having hooked the screw-driver, take an epiploon from a nest of the forward bearing of the camshaft.
7. Before installation of a new epiploon examine its working edge. It has to be equal, without vyryv, dents and flows of rubber. The spring of an epiploon has to be whole and unextended. Oil a working edge engine.

    
GOOD ADVICE
For simplification of a press fitting of an epiploon make on its landing edge a small facet by means of a file or a small emery circle.

8. Establish an epiploon by a working edge in a bearing nest, accurately fill a working edge on the camshaft (for example, by means of a wooden stick) and press against the stop by means of a suitable mandrel. As a mandrel it is possible to use an old epiploon.
9. Establish all removed details and knots as it should be, the return to removal.
10. Adjust a tension of belts of the drive of the generator and pump of the hydraulic booster of steering (see. "Check and adjustment of a tension of a belt of the drive of the generator and pump of the hydraulic booster of steering"), and also the conditioner compressor (see. "Check and adjustment of a tension of a belt of the drive of the compressor of the conditioner").

"previous page
5.7.3. Replacement of oil scraper caps
following page"
5.7.5. Replacement of epiploons of a bent shaft