Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
7.1. Forward suspension bracket
7.1.1. Features of a design
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
7.1.3. Removal and installation of a damping rack
7.1.4. Repair of a damping rack
7.1.5. Replacement of the top support of a damping rack
7.1.6. Replacement of a spherical support of a damping rack
7.1.7. Replacement of the lever of a forward suspension bracket
7.1.8. Replacement of details of the stabilizer of cross stability of a forward suspension bracket
7.1.9. Replacement of the bearing of a forward nave
7.2. Back suspension bracket
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








59d80679 оборудование +для офтальмолога


7-1-3-snyatie-i-ustanovka-amortizatornojj-stojjki.html

7.1.3. Removal and installation of a damping rack

It will be required to you: keys "on 9", "on 12", "on 19", face heads "on 32", a key for bolts of wheels, a neck, a stripper of spherical hinges, small beards, the hammer.
1. Slow down the car the parking brake and establish an antiretractable emphasis ("boots") under back wheels.
2. Weaken an inhaling of a nut of fastening of a nave.
3. Weaken an inhaling of bolts of fastening of a wheel.
    
PREVENTION
Weaken and tighten bolts of fastening of a wheel only on the car standing on the earth.

4. Open a cowl, hook the screw-driver …
5. … also remove a protective cover of the top support of a telescopic rack.
6. Holding one key a shock-absorber rod from a provorachivaniye, the second key weaken a nut inhaling (if you remove a telescopic rack for replacement of the shock-absorber, a spring or the top support).
7. Weaken an inhaling of three nuts of fastening of the top support.
8. Raise a forward part of the car and establish on reliable support.
9. Remove a wheel.
10. Turn out bolts of fastening of a support, remove a support in collecting (see. "Replacement of a support of the forward brake mechanism"), without disconnecting a brake hose, also suspend it on a wire.
11. Turn out the lock screw and remove a brake disk (see. "Replacement of a brake disk").
12. Turn off a nut of a finger of a tip of steering draft and a vypressuyta a finger from the rotary lever of a telescopic rack (see. "Replacement of an external tip of steering draft").
13. Remove a spring clamp of a nut of fastening of a finger of a spherical support, turn off a nut and a vypressuyta a finger (see. "Replacement of a spherical support of a damping rack").
14. Turn off a nave nut …
15. … remove a washer, bring a shaft of the external hinge of equal angular speeds out of a nave of a wheel and suspend the drive of a forward wheel on a wire.
    
PREVENTION
During the work be careful not to damage a protective cover of the CV JOINT as work on its replacement very labor-consuming.

16. Finally turn off three nuts of fastening of the top support to a body, remove washers (if are established) and remove a telescopic rack assembled.
17. Establish a telescopic rack as it should be, the return to removal. Finally tighten a nave nut on the car standing on the earth, the moment specified in the appendix 1.
18. After an inhaling stop a nut to small beards and the hammer.

NOTE
After replacement of a telescopic rack of a forward suspension bracket or its details check and if necessary adjust the angles of installation of wheels (see. "Check and adjustment of angles of installation of wheels"). Use services of the workshops having the special equipment.

"previous page
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
following page"
7.1.4. Repair of a damping rack